Single-/Dual-Supply Precision Analog Limiter Handles Wideband Signals

本文以PDF格式下载。

As the name implies, a limiter circuit (sometimes called a “clipper”) prevents a signal from exceeding desired thresholds, which would otherwise cause saturation and overload of the following stage. The circuit inFigure 1precisely limits the wideband input signal V_iat the V_REFlevel and can be used with both single and dual power supplies.

Output signal V_o1of the first stage, U1_1 (one-half of an LT1810, a dual 180-MHz, 350-V/µs low-distortion op amp), is precisely limited at the level of V_REF, but with inverse polarity compared with the input signal. U1_1 has a gain of ‒1 for the input signal V_i, and a gain of +2 for the reference signal V_REF。

Since the positive input of U1_1 is referenced to V_REF, the output signal is referenced to 2 × V_REF。Thus, while the input signal rises from zero to V_REF, the output signal of the first stage decreases from 2 × V_REFto V_REF。The second stage of limiter U1_2 is an inverting amplifier with the gain of ‒1. It’s referenced to the V_REFas well, and restores the original dc level and polarity of the input signal.

1. This analog circuit, based on the LT1810 op amp, precisely limits input signal V_iat reference level V_REF。

For the output of the first stage, V_o1= 2 × V_REF- V_iif V_i≤ V_REFand V_o1= V_REFif V_i≥ V_REF, while the output signal of the second stage is V_o2= 2 × V_REF‒ V_o1= V_i, if V_i≤ V_REF, and V_o2= V_REFif V_i≥ V_REF。(注意,output-dc水平,以及limiting point, may be shifted by an optional network of R6 and R7; otherwise, that network isn’t used.)

D1 is a part of the negative feedback of U1_1, making it an "ideal diode"—as soon as V_ireaches the V_REFlevel, U1’s output voltage increases until it compensates for voltage drop V_d二极管。When V_iis less than V_REFand D1 is turned off, diode D2 is on and sends the output current of U1 directly to its input. This prevents U1 from negative saturation, which would significantly decrease the switching speed of the first stage.

The voltage level on the output pin of U1_1 is (2 × V_REF) ‒ V_i+ V_d, and it reaches its maximum level with the minimum level of the input signal. This determines the maximum possible level of V_REF, which doesn’t cause the distortion of the limiter's output signal at its minimum level of V_REF= [(V+) + V_i- V_d]/2. Here, V+ is the maximum output voltage of op amp at the chosen V_CC, which is almost equivalent to V_CCfor the rail-to-rail op amp.

For the same reason, the minimum level of V_REFshould not be lower than V_d; however, the input signal may significantly exceed V_REF。

2. The LTspice simulation shows the limiter's response for a 1-MHz sine-wave signal (a) and a 2-µs piecewise-linear signal (b).

The LTspice simulation shows the limiter's responses for a 1-MHz sine-wave signal with 8-V peak-to-peak amplitude(Fig. 2a), and for a 10-V, 2-µs piecewise linear (PWL) signal crossing the limitation level several times(Fig. 2b), both with V_REFof 5.5 V. The limiter is quite accurate within the entire output-voltage range of the op amp. The simulation demonstrates that limitation errors don’t exceed 8 mV and output setting time is within 30 ns around the limitation point. When compared to the "simple op amp clipper" of Ref. 1, this limiter works at much-higher frequencies and with significantly lower distortion.

References

1. Thomas Mosteller and Aaron Schultz, "Op Amps Make Precision Clipper, Protect ADC"Electronic Design, November 2016.

2. Datasheet,LT1810 - Dual 180MHz, 350V/µs Rail-to-Rail Input and Output Low Distortion Op Amps。